What spoilers are you guys getting, if any?

[Integra23]

What's weird too is there has been slight inconsistencies. My front corner on the passenger side is slightly raised also, going to have to seal it.

Integra23 didn't have rubber washer around the threads

Mine did not arrive with those corner protectors that I saw in his videos.

Mine had the corner protectors..

Sponsored

 

[bpebler]

Mine had the corner protectors..

I guess I'd rather have the washers over the corner protectors but still...QC might need to improve at Artwork for consistency.

 

[StingertimeNC]

I just sent an email. Not sure what the remedy is. A replacement is likely to fit the same way.

At least Artwork will have my feedback. Seems like class action lawsuit is our only option. LOL.

The spoiler was not all that expensive, but the mental anguish is worth a lot of money!

 

[bpebler]

Yeah, a tad disappointing for sure.

 

[Compromise]

Looks good.

I guess all of our front corners stick up. Bummer. Makes sense though, they all came from the same mold.

Thought it was only me.. there's a gap towards the front part that gathers dirt/pollen. Quite annoying.

 

[StingertimeNC]

I'm collecting little pieces of pine straw and pine bark in the front edge. Definitely going to add some silicone

 

[Turbo Tater]

Just installed mine yesterday, and have all of the same issues. Lifts at the corners, gaps in the front, shipped without corner protectors..... I think it still looks good but just annoyed with the fitment.

 

[Compromise]

I'm collecting little pieces of pine straw and pine bark in the front edge. Definitely going to add some silicone

What silicone you adding?

 

[StingertimeNC]

Not sure. Anybody have suggestions? I didn’t take care of it yet.

 

[Tw1stedlog1k]

Are these all issues with the V2? Just curious

 

[Integra23]

Received a response along with a tracking number for the foam washers and replacement double face tape. Now do I try ads remove the monstrosity..

 

[StingertimeNC]

It's a hassle for sure. I received a response to my email asking for pics. Will send some in asap.

Yes, issues are with the V2 spoiler, although someone said their V1 spoiler also doesn't sit totally flush at the outside corners either. One thing I thought of is that I was so focused on side to side alignment I may not have had the spoiler pushed as far forward as possible. Although the mounting holes run side to side on the hatch, so I can't imagine there's any room to push it forward all that much. Knowing what I know now, I don't think I would buy it. It's pretty cool, just wish it fit better. Maybe if I removed it, and replaced all the double sided 3m tape and try again I could improve it somewhat. I'll post up pics when I get a few minutes.

 

[creaturemachine]

Don't all your OE lip spoilers collect gunk too, or is this one just collecting bigger stuff? Mine does, and that's because it has to drain underneath otherwise you'd have a puddle on the hatch. I think if you siliconed the bat-wing it'd double as a bath tub.

 

[Integra23]

Don't all your OE lip spoilers collect gunk too, or is this one just collecting bigger stuff? Mine does, and that's because it has to drain underneath otherwise you'd have a puddle on the hatch. I think if you siliconed the bat-wing it'd double as a bath tub.

Don't all your OE lip spoilers collect gunk too, or is this one just collecting bigger stuff? Mine does, and that's because it has to drain underneath otherwise you'd have a puddle on the hatch. I think if you siliconed the bat-wing it'd double as a bath tub.

With the weather it's acting more as a hot tub.

 

[StingertimeNC]

Don't all your OE lip spoilers collect gunk too, or is this one just collecting bigger stuff? Mine does, and that's because it has to drain underneath otherwise you'd have a puddle on the hatch. I think if you siliconed the bat-wing it'd double as a bath tub.

That's a really good point. OEM lip spoiler definitely allowed water through it, as well as catching small dirt and pollen and stuff. The gap was just tighter so less noticable.

Yes the V2 is catching some bugger stuff along the front edge, but maybe it is just best to leave it alone so water can escape.

Ugh, what to do.

Sponsored