Sponsored


Baozzer 2024 A-Spec Tech 6MT

OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
I have the PRL HVI, but how do you like the K&N intake? Wondering if there’s much of a difference or worth the swap.

Car looks amazing by the way!
I only have the drop in air filter that’s like $50 with the stock intake. It makes the car a bit louder. I’m happy without an intake. From what I know k&n is more loud and you can hear more turbo sounds. But if you already have the hvi I don’t think it’s worth the upgrade.
Sponsored

 
OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
Spacers are a no go ❌. Will wait until I find a nicer pair of wheels on the low LOL.
Acura Integra Baozzer 2024 A-Spec Tech 6MT 9FB94BF0-0F2C-47C0-9819-6F014559D936
Acura Integra Baozzer 2024 A-Spec Tech 6MT F1C6F85A-D0DA-438F-8C10-063CB9DEAC25
 
OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
I honestly rather not do that LOL.
 

Sponsored

OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
Those cut out on the stock rim are not low enough for the studs.
 

SeanIsElsewhere

Senior Member
First Name
Sean
Joined
May 18, 2022
Threads
13
Messages
528
Reaction score
256
Location
Philadelphia, PA
Car(s)
2023 Acura Integra A-Spec Tech
I'm so confused: what is actually interfering with the wheel and/or spacer? Why can't the wheel sit flush?
The spacers have their own lugs and holes for your stock lugs to pass through. With a 20mm or less spacer, the original lugs make contact with this bored out spaces in the back of the wheel whereas with the 25mm+, the tip of the lug doesn’t contact it.
I’m unsure what is causing the non-flush fitment of the spacer to the hub though; that I haven’t experienced or seen posted about
 
OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
You answers your own question LOL. It’s because the lugs are contacting the rim before it reaches the hub
 

creaturemachine

Senior Member
First Name
Brad
Joined
Mar 20, 2023
Threads
1
Messages
263
Reaction score
243
Location
Canada
Car(s)
2023 Integra 6MT
It's probably just a few mm of material in your way. You wouldn't harm the wheel much removing it. I'll bet some people just torque it down and let the studs do it.
 

Sponsored

OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
That is def not something I would like to risk. Purposely dremmeling into the rim. No thanks.
 

SeanIsElsewhere

Senior Member
First Name
Sean
Joined
May 18, 2022
Threads
13
Messages
528
Reaction score
256
Location
Philadelphia, PA
Car(s)
2023 Acura Integra A-Spec Tech
Just gotta dremmel the holes, cut the oem lugs shorter or torque those lugs down eaxtra to close the gap it seems. Either that or run a larger spacer
 
OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
The best approach would be to try 25mm spacers. Idk just drilling into the rim and throwing off the balance or worse case scenario starting a pilot hole for a large crack is not worth it. Trimming the stocks bolt would be cake but I would rather go the replacement lug route at that point
 

6-Speedio

Senior Member
Joined
Jun 28, 2023
Threads
0
Messages
56
Reaction score
43
Location
Canada
Car(s)
Civic Type R
Just gotta dremmel the holes, cut the oem lugs shorter or torque those lugs down eaxtra to close the gap it seems. Either that or run a larger spacer
Cutting the original lugs is a bad idea and a great way to end up with stripped lug nuts. It would be best to replace the lugs with aftermarket, shorter pieces instead.
 
OP
OP
Baozzer

Baozzer

Senior Member
First Name
Bao
Joined
Jun 13, 2023
Threads
4
Messages
154
Reaction score
62
Location
FL
Car(s)
2024 A-Spec Tech 6MT
Build Thread
Link
I’m just not going to put any spacers now! LOL. I’m okay with how she’s sitting until new shoes 👀
Sponsored

 
 



Top