Parking w/ brake Control Module location?

[c34webb]

I purchased this module to repair my wrecked 24 integra. Can't seem to find out where in the world it goes. Any ideas? part number 39670-3S5-A05

Sponsored

 

[akoza]

Not sure whether this will be of any help, but on the RDX it's in the rear left C- (or D-?) pillar, according to the link below. May be a good place to start looking on the Integra.

https://acura.bernardiparts.com/Images/Install/2021_RDX_ParkingSensors_BII14291-26.pdf

The diagram on Dreamshop also shows the Integra one toward the left rear side, although it's not as specific as to where it's located. Good luck!

 

[jayy_swish]

Interior Trim Area File it will be listed as "AC" in the diagram

EDIT: realize the file doesn't look as easy to read as the online format lol, but if you scroll down you'll see it under the AC sub procedure. Ill attach a picture for your convenience

View attachment Interior Trim Area (Interior Moulding _ Trim).pdf

View attachment Parking and Back-Up Sensor System Component Location Index (Except Type-S) (Collision Avoidanc...pdf

 

[c34webb]

Interior Trim Area File it will be listed as "AC" in the diagram

EDIT: realize the file doesn't look as easy to read as the online format lol, but if you scroll down you'll see it under the AC sub procedure. Ill attach a picture for your convenience

View attachment Interior Trim Area (Interior Moulding _ Trim).pdf

View attachment Parking and Back-Up Sensor System Component Location Index (Except Type-S) (Collision Avoidanc...pdf

Thanks so much! Found it, replaced it and still an issue. Dang.

 

[jayy_swish]

Thanks so much! Found it, replaced it and still an issue. Dang.

What code are you getting from the module? Or is it a no communication issue

 

[c34webb]

What code are you getting from the module? Or is it a no communication issue

B2600-54. Not sure what that equates to.

 

[jayy_swish]

B2600-54 is parking sensor not initialized, try doing the rest on the parking module:

EDIT: just saw your other thread. Can you try erasing the code and seeing if it’s selectable? If not I would go into the data list in the module and see if all sensors are providing data

View attachment Resetting The Parking and Back-Up Sensor Control Unit (Collision Avoidance Module).pdf

 

[c34webb]

B2600-54 is parking sensor not initialized, try doing the rest on the parking module:

EDIT: just saw your other thread. Can you try erasing the code and seeing if it’s selectable? If not I would go into the data list in the module and see if all sensors are providing data

View attachment Resetting The Parking and Back-Up Sensor Control Unit (Collision Avoidance Module).pdf

Yeah I’m not able to reset the PSR system via the dash since the function is in red. The data shows every sensor at 0 yrds even on a moving graph while moving objects closer to the sensors.

 

[jayy_swish]

If there's no data being transmitted when you move something closer or further away then I would verify power and grounds at the module and then at the individual sensors.

As an added check I would verify the connection from the sensors to the module by Ohms checking the wires, just to rule out an open circuit, and check for a short also.

View attachment Parking and Back-Up Sensor Connector.pdf

View attachment Parking and Back-up Sensor System (KA USA DE4) (Collision Avoidance and Parking Assist Systems).pdf

 

[c34webb]

If there's no data being transmitted when you move something closer or further away then I would verify power and grounds at the module and then at the individual sensors.

As an added check I would verify the connection from the sensors to the module by Ohms checking the wires, just to rule out an open circuit, and check for a short also.

View attachment Parking and Back-Up Sensor Connector.pdf

View attachment Parking and Back-up Sensor System (KA USA DE4) (Collision Avoidance and Parking Assist Systems).pdf

Excellent stuff. Running the multimeter on the control unit connector I'm using the power source (10) to the ground control units ground (15) 12.3v, Ground for from sensors (5) 10v, and Ground from rear sensors (16) .002v. Not sure why I'm getting such a variance but I assume somethings going on with the rear sensor which is weird because there was never any damage in the rear only the front.

Hoping you might have some ideas.
I owe you big time.!

 

[jayy_swish]

Excellent stuff. Running the multimeter on the control unit connector I'm using the power source (10) to the ground control units ground (15) 12.3v, Ground for from sensors (5) 10v, and Ground from rear sensors (16) .002v. Not sure why I'm getting such a variance but I assume somethings going on with the rear sensor which is weird because there was never any damage in the rear only the front.

Hoping you might have some ideas.
I owe you big time.!

For the rears try placing the cars in reverse and see if you get the 12v while using the ground (16). next step might be tedious, but you gotta check out each individual sensor and see if they’re getting the 12 V to be sure

edit: I dont see any indication whether the sensors are ground switched or power switched. But my guess is like most modules it’s ground switched

Sponsored