What did you do to your Integra Type S today? 🙋🏻‍♂️

[Wolfman]

The plastic pieces come prepainted and the metal pieces come primed from what I've seen.

These fenders are stupid cheap, though. I've found a few oem sources for less than 200$, which you could have your local dealer price match. Raw primed panel should be pretty cheap to have painted since there's virtually no prep work. If you have a pearl finish, it will never look 100% matched. They can get 99% close, and most people won't notice, but if you have a sharp eye, you're better off having a custom paint shop take their time blending. The average body shop will not be able to do it perfectly, despite any claims.

I think there are a few online dealers of "prepainted oem parts" which you can purchase. They like to charge about 500$ per panel in addition to cost of the panel. I've seen them but personally have no experience using them.

Thanks I figured. With the car being only a few months old I am just not thrilled to blend the door, hood, and bumper :/… but I think I’m SOL and need to do it.

Sponsored

 

[gohan408]

added more carbon and a new knob

 

[myhdnromance]

I saw a fender on eBay not long ago but not sure what side you need. The one side was pretty fubar

My current situation.

 

[ABPDE5]

I saw a fender on eBay not long ago but not sure what side you need. The one side was pretty fubar

My current situation.

Noticeable improvement?

 

[myhdnromance]

Noticeable improvement?

I haven't taken her out of the garage yet since its been raining here, but tapping around inside the car it seems to have cut down on the hollow sounds

Correction post drive. Huge difference. Not as tin can sounding from the exhaust in the rear….added picture where I stopped and placed everything at 4 am

 

[PrecordFK7]

First post on this thread so I'll post a bunch of stuff done in the past month+, just put the Spoon Bump Steer (roll center adjusters) and rear A/C vents in the car. Previously had the PowerFlex Antilift Kit installed and wasn't able to find anyone that's installed an Antilift Kit on the FL5 or DE5 so far. Things changed from the FK8/10th Gens and the subframe has to be dropped to remove the lower control arm to install the ALK.

Also, just finished up installing the Full-Race HPFP, Hondata 1530cc Injectors, CANFlex, PTFE Lines, Radium Fuel Filter and pressure gauge, JSR ported Intake Manifold, ported throttle body, ported turbo outlet pipe, and finished with a custom Jester Tune.

 

[Tw1stedlog1k]

Curious what your build goals are?

 

[PrecordFK7]

Curious what your build goals are?

A turbo is next for sure, still deciding on which one and saving up for it, but that'll pretty much do it for all the major mods. Will address some extra cooling too.

 

[new2teg]

Installed carbon mirror caps from Jogon. Fit is spot on. A bit thin but I think it's nice for the price.

 

[dockleryxk]

It's been a tough month for my car. Had to get a new windshield and got rear-ended at the Tail of the Dragon

 

[crepr12]

So what ran into at the Dragon?...

 

[Integra23]

So what ran into at the Dragon?...

Motorcycle

 

[TwinSkrullDesign]

Just shipped out my ECM to be unlocked ??

 

[gohan408]

Installed carbon mirror caps from Jogon. Fit is spot on. A bit thin but I think it's nice for the price.

is it an overlay or replacement cap?

 

[gohan408]

It's been a tough month for my car. Had to get a new windshield and got rear-ended at the Tail of the Dragon

love the big ol tri exhaust. tips

Sponsored